Skip to content

What does the EU Machinery Regulation change for machine manufacturers?

Hefmec expert performing an FEM analysis

The EU Machinery Regulation (EU) 2023/1230 replaces the Machinery Directive 2006/42/EC and applies from 20 January 2027. The basis of CE marking stays the same: the manufacturer assesses the risks, compiles the technical documentation, draws up the declaration of conformity and affixes the CE marking. The changes concern conformity assessment procedures, CE marking and instructions for use, modifications made to machinery later, and software and artificial intelligence.

We reviewed the Regulation from a designer’s point of view. This article explains which changes affect the everyday work of machinery and lifting accessory manufacturers and what to check before 20 January 2027.

What does the change from a directive to a regulation mean?

The Machinery Directive had to be transposed into each member state’s national legislation. The Machinery Regulation is directly binding in all member states, so the requirements and their wording are the same throughout the EU. The manufacturer bases conformity on a single text, regardless of the country the machine is delivered to.

The Regulation entered into force on 19 July 2023 and applies from 20 January 2027. There is no parallel transition period: a machine placed on the market or put into service on or after 20 January 2027 is assessed under the Machinery Regulation. Machinery placed on the market under the Machinery Directive before that date may still be made available (Article 52).

What changes in conformity assessment?

The Machinery Regulation divides conformity assessment into modules familiar from other EU product legislation. The manufacturer chooses the module depending on whether the machine is listed in Annex I of the Regulation (Article 25).

ModuleWhat it meansNotified body
A – internal production controlThe manufacturer assesses and declares conformity itselfNo
B + C – EU-type examination and conformity to typeA notified body examines the type, the manufacturer ensures production conforms to itYes, type examination
H – full quality assuranceThe manufacturer’s quality system covers design, manufacture and testingYes, quality system assessment
G – unit verificationA notified body verifies each individual machineYes, every machine

Part A of Annex I includes, for example, vehicle servicing lifts as well as safety components and machinery whose safety functions rely on machine learning and fully or partially self-evolving behaviour. Their assessment always requires a notified body. For machinery in Part B, such as certain circular saws and planing machines for woodworking, module A is allowed only if the machine is designed in accordance with harmonised standards or common specifications covering all relevant essential requirements. For all other machinery, module A is sufficient.

Module G is new in machinery assessment. It suits special machines built as one-offs, where type examination of a series makes little sense.

Lifting accessories are not listed in Annex I, so module A continues to apply to them. The Machinery Regulation does not change the way we design, verify and CE mark lifting accessories. Strength verification is, however, affected by the EN 13155 update, which we explain in the article on proof load testing of lifting accessories and the EN 13155 update.

What changes in CE marking and product markings?

The CE marking is still affixed to the machine visibly, legibly and indelibly. What is new is that where this is not possible or not warranted on account of the nature of the machine, the marking is affixed to the packaging and to the accompanying documents (Article 24).

This matters especially for small lifting accessories and components. Small items have been designed larger just so that the CE marking would fit on them. In future, the designer can dimension the part for its function and move the marking to the packaging and documents where this is justified.

In addition to the postal address, the manufacturer’s contact details include a website, an e-mail address or another digital contact. The machine must also carry a description of the model or type, the year of construction and a serial or batch number or other identification. Where the size or nature of the machine does not allow this, the information is given on the packaging or in an accompanying document (Article 10).

What changes in instructions for use and the declaration of conformity?

Instructions for use may be supplied in digital form. In that case, the manufacturer must

  • indicate on the machine or, where that is not possible, on its packaging or in an accompanying document how the digital instructions can be accessed,
  • provide the instructions in a format that the user can print, download and save, and
  • keep the instructions available online for the expected lifetime of the machine and for at least ten years.

If the user requests printed instructions at the time of purchase, the manufacturer must provide them free of charge within one month. For machinery intended for consumers, safety information must always be provided in paper form (Article 10(7)).

The EC declaration of conformity becomes the EU declaration of conformity, whose content follows the model in Annex V. The declaration can accompany the machine, or the manufacturer can give an internet address or a machine-readable code in the instructions for use where the declaration is available. The declaration no longer names a person authorised to compile the technical documentation.

The content of the technical documentation is described in more detail in Annex IV. The manufacturer keeps it and the declaration for at least ten years. If the safety of the machine relies on software, the authority may, upon a reasoned request, require access to the source code or programming logic.

When does the person modifying a machine become its manufacturer?

The Machinery Directive did not define when a modification to an existing machine is significant enough to make the person who carries it out the manufacturer. The Machinery Regulation defines a substantial modification (Article 3(16)). A modification is substantial when

  1. it is made physically or digitally after the machine has been placed on the market or put into service,
  2. it was not foreseen or planned by the manufacturer,
  3. it creates a new hazard or increases an existing risk, and
  4. controlling that risk requires either guards or protective devices that involve modifying the existing safety-related control system, or additional protective measures to ensure the stability or mechanical strength of the machine.

The person who carries out a substantial modification is considered a manufacturer (Article 18). They must ensure that the modified machine complies, carry out the conformity assessment procedure and draw up the EU declaration of conformity. Smaller modifications do not make the person a manufacturer, but their effect on safety should still be assessed and documented.

The point on mechanical strength directly concerns lifting accessories and load-bearing structures. When the working load limit (WLL) of a lifting accessory is increased, its intended use is changed or its structure is reinforced by welding, the person making the change is typically in the position of a manufacturer. For such modifications, we carry out a risk assessment and structural analysis and prepare new CE documentation.

Before making a modification, ask three questions: Has the manufacturer foreseen the modification, for example in the instructions for use? Does it create a new hazard or increase a risk? Does controlling the risk require changes to the safety-related control system or to the strength of the structure? If the manufacturer has not foreseen the modification and the answer to the last two questions is yes, the modification is substantial.

What do software, AI and cybersecurity bring?

A safety component can also be software placed on the market separately (Article 3). A safety function can therefore be implemented in code without a separate physical component, provided it meets the same requirements.

If a safety function relies on machine learning and self-evolving behaviour, the machine or component falls under Part A of Annex I. The control system must not allow changes to settings or rules that could lead to hazardous situations – not even during the learning phase of the machine.

Cybersecurity is part of the essential safety requirements (Annex III, section 1.1.9). A device connected to the machine or a remote connection must not lead to a hazardous situation. Software and data critical to safety must be protected against intentional and accidental corruption, and the machine must be able to identify the safety software installed on it. A tracing log of safety software updates must be available for five years (section 1.2.1).

The Machinery Regulation does not require security updates to be released during the use of the machine. Such an obligation may come from the Cyber Resilience Act (EU) 2024/2847 if the machine has digital elements.

What should manufacturers check before 20 January 2027?

  • Declaration template: EU declaration of conformity following Annex V, without the name of the person compiling the technical documentation.
  • Machine category: whether the machine is listed in Annex I and which module applies.
  • Instructions for use: digital delivery, availability for at least ten years and printed instructions on request.
  • Markings: whether the CE marking and identification fit on a small product, or are given on the packaging and in documents.
  • Traceability: records of who supplied the product and to whom it was supplied are kept for ten years (Article 19).
  • Software: identification of the safety software version and an update log.
  • Quotations: the applicable legislation and standard version, for lifting accessories EN 13155:2020+A1:2025.

Do you have any questions?

We prepare risk assessments, structural analyses and technical documentation for new machinery and lifting accessories and for modifications to existing machinery. Read more about our mechanical design services.

For questions about the Machinery Regulation and CE marking, contact Petja Lindström directly, +358 40 740 4771.

Read also

Whether you have a big or small production engineering problem, we can solve it. Contact us on +358 9 388 2050 and tell us your needs. Let’s create a more efficient future together.

Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.